Announcement

Collapse
No announcement yet.

Autocross alignment specs?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • mustangtomiata
    replied
    RE: Autocross alignment specs?

    Honestly, it could have been a little bit of both. You could have been over driving but your car also could have just been pushing. amaff was saying there was dirty pavement and that could have been a big factor in your understeer but as far as driving goes be smooth and don't try and go balls to the wall first time out, drive agressively but not 10/10ths and slowly build your speed. Then you will notice when your start over driving. Also coming up to the sweeper was there any braking or was it just an off throttle turn?

    Leave a comment:


  • matthew
    replied
    RE: Autocross alignment specs?

    Originally posted by Roadster
    Glad to see you found the forums, Matt.

    Did you pick up another Miata?
    someone buy my subaru please. haha

    Leave a comment:


  • Roadster
    replied
    RE: Autocross alignment specs?

    Glad to see you found the forums, Matt.

    Did you pick up another Miata?

    Leave a comment:


  • matthew
    replied
    RE: Autocross alignment specs?

    On my CSP miata I was running 450F/300R but would have liked something a little stiffer. No rear swaybar.

    On mine....

    FRONT
    camber: -2.0
    caster: 4.X (cant remember)
    tow: +1/16

    REAR
    camber: -2.5
    tow: -1/16

    Leave a comment:


  • amaff
    replied
    RE: Autocross alignment specs?

    That combined with the suspension I'm running is very neutral in sweepers, slaloms ALMOST as good as a CRX (puller instead of pusher...), but gives just enough throttle on oversteer (or throttle off oversteer, whichever you perfer)

    Leave a comment:


  • Jack-MX5ATLanta.com
    replied
    RE: Autocross alignment specs?

    I was in the 3rd run group. It could have just been that corner and the general speeds involved. When I was working it I noticed alot of people having issues tackling it. What kind of a balance does that setup give you?

    Leave a comment:


  • amaff
    replied
    RE: Autocross alignment specs?

    what run group were you in? I ran in the 1st heat aka the street sweeper heat and all I had was understeer, everywhere. It didn't even dawn on me what the problem was (not really the car, but how I was driving on dirty pavement) until the 4th run group where I ran TO and had a TON more grip just from the course being clean. The front end was biting, and the rear was dancing right where I needed it. I shaved a full second on my 1st TO run in the miata from my fastest time in the morning.


    To answer the original question (though I know I posted this on here at some point)
    Front
    Camber: -2.5
    Caster: 4.5-ish
    Toe: 1/8" out total

    Rear
    Camber: -2.0
    Toe: 1/16" in total.

    Leave a comment:


  • Jack-MX5ATLanta.com
    replied
    RE: Autocross alignment specs?

    I could do with letting some of the more experienced auto'xers having a run in my car and seeing if its a balance issue or just me. I know for sure there are a few seconds to be cut from my times. I just need to figure out where I'm going wrong. Most likely too fast in the wrong places.

    Leave a comment:


  • Jack-MX5ATLanta.com
    replied
    RE: Autocross alignment specs?

    I don't think this was the case where it was hurting the most on the decreasing radius sweeper. I was taking it really wide waiting for the point to turn in, not going particularly fast, and it just kept on going. Should I be more gradual on the throttle? I wouldn't have thought with the power of a 1.8 it would be too much of an issue.

    Leave a comment:


  • Tinman88
    replied
    RE: Autocross alignment specs?

    If roll is controlled and it's neutral through corners, you may just be coming into the corners too hot.

    "In slow, out fast."

    Leave a comment:


  • Jack-MX5ATLanta.com
    replied
    RE: Autocross alignment specs?

    According to their website they're 318 front, 233 rear and they're paired with some Bilstein HD's from the advice of fatcatmotorsports. It's a street and autox setup. I'm currently running without the rear bar but I don't think the rates are high enough in the rear to compensate for the lack of it.

    Body Roll isn't really an issue any more, and it remains very steady through corners, it's just when it comes time to dive in and turn it likes to push rather than rotate.

    Leave a comment:


  • Tinman88
    replied
    RE: Autocross alignment specs?

    What spring rates are you running? The CSP NC is on 400#/300# IIRC, and is waaaay undersprung, but it's also a lot heavier--NAs in STS2 typically run about 700/450. Big front bar and no rear bar and it's VERY neutral, just upsets easily in quick transitions.

    I believe when I got it aligned I got something like -2.5*F/-3.0*R camber, as much caster as possible in the front, and a bit of toe out in the front (maybe 1/8" or 1/4" total), none in the rear.

    Leave a comment:


  • JDM88
    started a topic Autocross alignment specs?

    Autocross alignment specs?

    My alignment seems to be a bit out of kilter since I've put the flyin miata springs and bilstein's on, it looks like it's got more negative camber than the tower of Pisa. What do the autox'ers on here run?

    I noticed I had some harsh understeer this last event, I think that might be due to disconnecting the rear sway bar to see how it felt. I think I'll either be putting that back on or buying a bigger new one before the alignment.
Working...
X